Authorized Distributor
Shopping Cart
0 items
 

ArduPilot - Arduino Compatible UAV Controller w/ ATMega328

ArduPilot - Arduino Compatible UAV Controller w/ ATMega328
Click to enlarge
Price: Rs.1,980.00
Availability: Back-ordered coming in 15 days
Model: ArduPilot-328
Average Rating: Not Rated

ArduPilot is a fully programmable autopilot that requires a GPS module and infrared XY and Z sensors to create a functioning Unmanned Aerial Vehicle (UAV). The autopilot handles both stabilization and navigation, eliminating the need for a separate stabilization system. It also supports a "fly-by-wire" mode that can stabilize an aircraft when flying manually under RC control, making it easier and safer to fly. The hardware and software are all open source. The board comes with all the surface-mount parts already soldered, but requires the user to solder on connectors. Firmware is already loaded, but the autopilot software must be downloaded and loaded onto the board by the user. It can be programmed with the Arduino IDE.

We highly recommend the following items to accompany this product:

  • An EM406 GPS module
  • An FTDI Basic or FTDI cable for programming
  • An extended EM406 GPS cable
  • An Expansion Board with airspeed sensor
  • XY and Z sensors
Features:
  • Controller designed to be used with autonomous aircraft, car or boat. Infrared sensor required only for aircraft.
  • Based on a 16MHz Atmega328 processor. Total onboard processing power aprox 24 MIPS.
  • Built-in hardware failsafe that uses a separate circuit (multiplexer chip and ATTiny processor) to transfer control from the RC system to the autopilot and back again. Includes ability to reboot the main processor in mid-flight.
  • Multiple 3D waypoints  (limited only by memory)
  • Comes with a 6-pin GPS connector for the 1Hz EM406 GPS module.
  • Has six spare analog inputs (with ADC on each) and six spare digital input/outputs to add additional sensors
  • Supports addition of wireless downlink module for telemetry
  • Can be powered by either the RC receiver or a separate battery
  • Hardware-driven servo control, which means less processor overhead, tighter response and no jitters.
  • Four RC-in channels (plus the autopilot on/off channel) can be processed by the autopilot. 
  • LEDs for power, failsafe status, autopilot status and GPS lock

Dimensions: 30mm x 47mm

Write Review
Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad            Good

Enter the code in the box below:

There are no additional images for this product.
Follow @SUMEETeSHOP
ArduPilot - Arduino Compatible UAV Controller w/ ATMega328

ArduPilot is a fully programmable autopilot that requires a GPS module and infrared XY and Z sensors to create a functioning Unmanned Aerial Vehicle (UAV). The autopilot handles both stabilization and navigation, eliminating the need for a separate stabilization system. It also supports a "fly-by-wire" mode that can stabilize an aircraft when flying manually under RC control, making it easier and safer to fly. The hardware and software are all open source. The board comes with all the surface-mount parts already soldered, but requires the user to solder on connectors. Firmware is already loaded, but the autopilot software must be downloaded and loaded onto the board by the user. It can be programmed with the Arduino IDE.

We highly recommend the following items to accompany this product:

Features:
  • Controller designed to be used with autonomous aircraft, car or boat. Infrared sensor required only for aircraft.
  • Based on a 16MHz Atmega328 processor. Total onboard processing power aprox 24 MIPS.
  • Built-in hardware failsafe that uses a separate circuit (multiplexer chip and ATTiny processor) to transfer control from the RC system to the autopilot and back again. Includes ability to reboot the main processor in mid-flight.
  • Multiple 3D waypoints  (limited only by memory)
  • Comes with a 6-pin GPS connector for the 1Hz EM406 GPS module.
  • Has six spare analog inputs (with ADC on each) and six spare digital input/outputs to add additional sensors
  • Supports addition of wireless downlink module for telemetry
  • Can be powered by either the RC receiver or a separate battery
  • Hardware-driven servo control, which means less processor overhead, tighter response and no jitters.
  • Four RC-in channels (plus the autopilot on/off channel) can be processed by the autopilot. 
  • LEDs for power, failsafe status, autopilot status and GPS lock

Dimensions: 30mm x 47mm

Rs.1,980.00